ClickMonitorDDC - Sterowanie monitorem

OXYGEN THIEF

Bardzo aktywny
Członek Załogi
Administrator
Dołączył
26 Maj 2010
Posty
35567
Reakcje/Polubienia
24595
Miasto
Trololololo
window.png



ClickMonitorDDC to mały, bezpłatny i przydatny program za pomocą którego możemy sterować monitorem bez sięgania do przycisków. Program pozwala między innymi na ustawianie jasności, kontrastu oraz barwy wyświetlanego obrazu. ClickMonitorDDC nie wymaga instalacji.

Zaloguj lub Zarejestruj się aby zobaczyć!


Zaloguj lub Zarejestruj się aby zobaczyć!
 

Jarom

Bardzo aktywny
Zasłużony
Dołączył
23 Wrzesień 2016
Posty
3893
Reakcje/Polubienia
1228
ClickMonitorDDC 4.1.0.1
4.1.0.1
Monitor name should be defined in EDID using 0xFC descriptor, external monitors normally do this, but internal LCD-Display
often do not implement this 0xFC descriptor, instead sometimes there is a 0xFE descriptor, which means unspecified text,
ClickMonitorDDC now uses this unspecified text for monitor name if there is no concrete monitor name definition.

If a monitor is connected to graphics card, the monitor gets detected, that means EDID-information can be read by graphics-card,
the monitor can be switched off or even disconnected from power-supply, nevertheless EDID can be read,
because graphics-card delivers power to read monitor EEPROM.
Therefore a switched off or powered off monitor is listed in ClickMonitorDDC, but cannot be controlled.
Normally you should not plug or unplug devices during running your computer, but monitors are in most cases hot-pluggable,
therefore ClickMonitorDDC now detects at once if a monitor is hot-plugged, earlier versions also detected hot-plugged monitors, but maybe later.

ClickMonitorDDC shows values between 0 - 100, which is fine with external monitors, but internal LCD-display may support less levels, often only 16 levels,
for instance 1 3 4 5 6 8 10 13 17 22 29 38 49 63 80 100. Windows says every laptop must report a maximum brightness level of 100,
but there are old laptops reporting for instance 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15.
These numbers only reflect a corresponding hardware-brightness-level and different Laptop models often have different numbers.
ClickMonitorDDC now recalculates level numbers to 0 - 100 in a linear more user-friendly way.

4.0.0.6
Behavior of the 8 timers for auto-run commands was improved.

4.0.0.0
ClickMonitorDDC now uses for Laptop-Display-handling WmiMonitorBrightnessEvent, WmiMonitorBrightness, WmiSetBrightness, GetMonitorRawEEdidV1Block.
Zaloguj lub Zarejestruj się aby zobaczyć!
 

Jarom

Bardzo aktywny
Zasłużony
Dołączył
23 Wrzesień 2016
Posty
3893
Reakcje/Polubienia
1228
ClickMonitorDDC 4.2.0.0
4.2.0.0
This is the actual download version. ClickMonitorDDC realizes hotkeys by keyboard/mouse-hooks.
Now these hooks run in a separate thread, this way mouse/keyboard-handling should always be smooth.


4.1.0.4

Moving settings window around could sometimes cause some incorrect redrawing of settings window. Fixed.

4.1.0.3
ClickMonitorDDC shows all devices connected to graphics card, maybe you have a AV Receiver connected,
which shows up as a monitor, but cannot be controlled or there is an additional monitor connected, you never use.
You can right click an uncontrollable device (which is listed with brightness ? contrast ?),
then you can click 'Ignore this monitor for saving time', from now on ClickMonitorDDC-window should open a little bit faster.
Click 'Monitor gets checked again' if for instance you want to control a rarely used monitor.
Clicking 'Copy Debug-Infos of all monitors to Clipboard' can be used to email some debug-infos to the program-author.
These are only some special data, not a complete feature-listing of the monitors.

4.1.0.2
ClickMonitorDDC was primarily developed to control external monitors in the most user-friendly way, for instance use mouse-wheel over icons or define hot-keys and so on.
Internal Laptop-LCD have built-in brightness-support by using FN-keyboard-keys or windows-sliders, but ClickMonitorDDC can also speed up handling of internal Laptop-LCD.
This version comes with an unique feature for Laptop-Displays, activate this feature in settings by clicking 'same Laptop-Brightness for battery and plugged',
from now on Laptop-Display keeps same brightness ignoring power-source-changes.
Windows 10 comes with an additional Battery saver feature, which can automatically lower brightness, so for instance brightness 100 is forced down to brightness 70,
there is no way to set brightness back to 100 if Battery saver with lower brightness option is active,
therefore 'same Laptop-Brightness for battery and plugged' is temporarily deactivated if Battery saver is detected.
Battery saver also gets automatically activated if 'Power saver' plan is chosen and Laptop is on battery.
Zaloguj lub Zarejestruj się aby zobaczyć!
 
Do góry